UBC Header

MAL

Publications

Highlighted authors are our graduate students or postdoctoral fellows.

Scopus Citation Index – Total Number of Journal Citations to the journal articles reported between 1996 and December 18, 2011: Excluding self citation of authors - 3887, h index: 35 (Citations prior to 1996 is not covered by Scopus. Google Scholar indicates over 5000 citations with h index of 41.)

Year 2010 2011
Journal Citation (excluding self citations) 588 618

  1. Kaymakci, M., Kilic, Z.M., Altintas, Y., 2012, “Unified Cutting Force Model for Turning, Boring, Drilling and Milling Operations”, Int. J. Machine Tools and Manufac,

  2. Xiaoliang, J., Altintas, Y., 2012, Prediction of micro-milling forces with finite element method, Journal of Materials Processing Tech.

  3. Altintas, Y., Verl, A., Brecher, C., Uriarte, L., Pritschow, G., 2011, “Machine tool feed drives”, CIRP Annals, Volume.60/2:779-796.

  4. Cao,H., Holkup, T., Altintas, Y., 2011, “A comparative study on the dynamics of high speed spindles with respect to different preload mechanisms”, International Journal of Advanced Manufacturing Technology, Pages 1-13, DOI: 10.1007/s00170-011-3356-9.

  5. Altintas, Y., Xiaoliang, J., 2011,”Mechanics of Micro-Milling with Round Edge Tools, Annals of CIRP, Vol. 60/1:77-80.

  6. Xiaoliang, J., Altintas, Y., 2010, “Slip-line Field Model of Micro-Cutting Process with Round Tool Edge Effect Journal of Materials Processing Technology”, J. Materials Processing Technology (in press).

  7. Heo, E.Y., Merdol, D., Altintas, Y., 2010, “High Speed Pocketing Strategy”, CIRP Journal of Manufacturing Science and Technology , (in press).

  8. Kurata, Y., Merdol, D., Altintas, Y., Suzuki, N., Shamoto,E., 2010, “Chatter Stability in Turning and Milling with in Process Identified Process Damping”, Japan Soceity of Mechanical Engineering J. Advanced Mechanical Design, Systems and Manufacturing”, vol.4/6: 1107-1118.   

  9. Yang, Y., Munoa, J., Altintas, Y., 2010, “Optimization of Multiple Tuned Mass Dampers to Suppress Machine Tool Chatter”, Int. J. Machine Tools and Manufac,  Vol.50/9, pp.834-842  

  10. Dombovari, Z., Altintas, Y., Stepan, G., 2010, “The Effect of Serration on Mechanics and Stability of Milling Cutters”,  International J. Machine Tools and Manufacture, Vol.50/6,  Pages 511-520.  

  11. Abele, E., Altintas, Y., Brecher,Y., 2010, “Machine Tool Spinde Units”,  Annals of CIRP, Keynote Paper, vol. 59/2, 781-802.

  12. Holkup,T., Cao,H., Kolár, P.,  Altintas, Y., Zelený,J., 2010, “Thermo-mechanical model of spindles”,  Annals of CIRP, vol. 59/1, pp:365-368.

  13. Altintas, Y., Sencer, B., 2010, “High Speed Contouring Control Strategy for Five-Axis Machine Tools”, Annals of CIRP, vol. 59/1, 417-420.

  14. Eyniyan, M., Altintas, Y., 2010, “Analytical Chatter Stability of Milling with Rotating Cutter Dynamics at Process Damping Speeds”, Trans. ASME, J. Manufac. Sc. and Eng. J. Manuf. Sci. Eng.  -- April 2010 --  Volume 132,  Issue 2, 021012 (14 pages) doi:10.1115/1.4001251

  15. Okwudire, C., Altintas, Y., 2009, Hybrid Modeling of Ball Screw Drives with Coupled Axial, Torsional and Lateral Dynamics, Trans. ASME, J. Machine Design. Vol.131/071002:1-9. (doi:10.1115/1.3125887)

  16. *Eyniyan, M., Altintas, Y., 2009, “Chatter Stability of General Turning Operations with Process Damping”, Trans. ASME, J. Manufac. Sc. and Eng. ,  Volume 131:4, 041005:1-10.

  17. Altintas, Y., Okwudire, C., 2009, “Dynamic Stiffness Enhancement of Direct-Driven Machine Tools using Sliding Mode Control with True Disturbance Recovery”, Annals of CIRP, Vol. 58/1, pp.335-338.

  18. *Okwudire, C., Altintas, Y., 2009, “Minimum Tracking Error Control of Flexible Ball Screw Drives using a Discrete-time Sliding Mode Controller”, Trans. ASME, J. Dynamic Systems, Measurement and Control, Volume 131,  Issue 5, 051006:1-12, doi:10.1115/1.3155005.

  19. *Sencer, B., Altintas, Y., “Modeling, and Control of Contouring Errors for Five-Axis Machine Tools. Part II - Precision Contour Controller Design”, Trans. ASME, J. Manufac. Sc. and Eng., vol. 131:3, pp. 031007:1-10.

  20. Sencer, B., Altintas, Y., Croft, E., 2009, “Modeling and Control of Contouring Errors for Five-Axis Machine Tools. Part I – Modeling”, Trans. ASME, J. Manufac. Sc. and Eng., vol. 131:3, pp. 031006:1-8.

  21. Altintas, Y., Stepan, G., Merdol, D., Dombavari, Z., 2008, “Chatter stability of milling in frequency and discrete time domain”, CIRP Journal of Manufacturing Science and Technology, vol.1,pp.35–44.

  22. Altintas, Y., Eyniyan, M., Onozuka, H., 2008, “Identification of Dynamic Cutting Force Coefficients and Chatter Stability with Process Damping”, Annals of CIRP, Vol. 57/1, pp. 371-374.

  23. Merdol, D., Altintas, Y., 2008, “Virtual Cutting and Optimization of Three Axis Milling Processes”, Int. J. machine Tools and Manufacture, vol.48 (10), pp. 1063-1071.

  24. Sencer, B., Altintas, Y., Croft, E., 2008, “Feed Optimization for 5 Axes CNC Machine Tools with Drive Constraints”, International Journal of Machine Tools and Manufacture, Vol. 48/7-8, pp. 733-745.

  25. Ferry, W., Altintas, Y., 2008, “Virtual Five Axis Milling of Impellers, Part – I: Feedrate Optimization of Five Axis Milling”, Trans. ASME, J. Manufac. Sc. and Eng. Vol. 130, pp. 0110013-1:13.

  26. Ferry, W., Altintas, Y., 2008, “Virtual Five Axis Milling of Impellers, Part – I: Mechanics of Five Axis Milling”, Trans. ASME, J. Manufac. Sc. and Eng., Vol. 130, pp. 011005-1:11.

  27. *Merdol, D.S., Altintas, Y., 2008, “Virtual Simulation and Optimization of Milling Operations: Part I –Optimization, Feed Rate Scheduling”, Trans. ASME, J. Manufac. Sc. and Eng., vol. 130, pp. 051005.

  28. Merdol, D.S., Altintas, Y., 2008, Virtual Simulation and Optimization of Milling Operations: Part I – Process Simulation”, Trans. ASME, J. Manufac. Sc. and Eng., vol. 130, pp. 051004.

  29. Altintas, Y., Merdol, D.S., 2007, “Virtual High Performance Milling”, Annals of CIRP, Vol. 55/1, pp. 81-84.

  30. Morgan, G., Cheng, R.Q., Altintas, Y., Ridgway, K.,  2007, “An expert troubleshooting system for the milling process”, International Journal of Machine Tools and Manufacture, Vol. 47/9, pp. 1417-1425.

  31. Turner, S., Merdol, D., Altintas, Y., Ridgway, K., 2007, “Modelling of the stability of variable helix end mills”, International Journal of Machine Tools and Manufacture, Vol. 47/9, pp. 1410-1416.

  32. Cao, Y., Altintas, Y., 2007, “Modeling of spindle-bearing and machine tool system for virtual simulation of milling operations”, International Journal of Machine Tools and Manufacture, Vol. 47/9, pp. 1342-1350.

  33. Roukema, J.C., Altintas, Y., 2007, "Generalized Modeling of Drilling Vibrations, Part II: Chatter Stability in Frequency Domain”, International Journal of Machine Tools and Manufacture, Vol. 47/9, pp. 1474-1485.

  34. Roukema, J.C., Altintas, Y., 2007, "Generalized Modeling of Drilling Vibrations, Part I: Time Domain Model of Drilling Kinematics, Dynamics and Hole Formation", International Journal of Machine Tools and Manufacture, Vol. 47/9, pp. 1455-1473.

  35. Ko, J.H., Altintas, Y., 2007, “Time Domain Modeling  of Plunge Milling Operations”, Int. J. Machine Tool Manuf. Eng., Vol. 47/9, pp. 1351-1361.

  36. Namazi, M., Altintas, Y., Abe, T., Rajapakse, N., 2007, “Modeling and Identification of Tool Holder – Spindle Interface Dynamics”, Int. J. Machine Tool Manuf. Eng., Vol. 47/9, pp. 1333-1341.

  37. Ko, J.H. , Altintas, Y., 2007, “Dynamics and Stability of Plunge Milling Operations”, Trans. ASME, J. Manufac. Sc. and Eng., Vol.129/1, pp. 32-40.

  38. Altintas, Y.,  Ko, J.H., 2006, “Chatter Stability of Plunge Milling”, Annals of CIRP, Vol. 55/1, pp.361-364.

  39. Erkorkmaz,K., Altintas, Y., Yeung, C.H., 2006, “Virtual Computer Numerical Control System”, Annals of CIRP, Vol.55/1, pp. 399-402.

  40. Kardes, N., Altintas, Y., 2006, “Mechanics and Dynamics of Circular Milling”, Trans. ASME, J. Manufac. Sc. and Eng., Vol.129/1, pp. 21-31.

  41. Roukema, J., Altintas, Y., 2006, “Time Domain Simulations of Torsional and Axial Vibrations of Drills”, Int. J. Machine Tool Manuf. Eng., Vol. 46/15, pp. 2073-2085.

  42. Yeung, C.H., Altintas, Y., Erkorkmaz, K., 2006, “Virtual CNC System – Part II: High Speed Contouring Application”, Int. J. Machine Tool Manuf. Eng., Vol. 46/10, pp. 1124-1138.

  43. *Yeung, C.H., Altintas, Y., Erkorkmaz, K., 2006, “Virtual CNC System – Part I: System Architecture”, Int. J. Machine Tool Manuf. Eng.. Vol. 46/10, pp. 1107-1123.

  44. Altintas,Y,  Brecher, C., Weck, M., Witt, S., 2005, “Virtual Machine Tool” , 2005 Keynote Paper of STC M, Annals of CIRP, Vol. 54/2, pp. 651-674.

  45. Altintas, Y., Cao, Y., 2005, “Virtual Design and Optimization of Machine Tool Spindles”, Annals of CIRP, Vol. 54/1, pp. 379-382.

  46. Albrecht, A.,  Park , S. S., Altintas, Y., Pritschow, G., 2005, “High frequency bandwidth cutting force measurement in milling using capacitance displacement sensors’’, Int. J. Machine Tool Manuf. Eng., Vol. 45/9, pp. 993-1008.

  47. Erkorkmaz, K., Altintas Y, 2005, “Quintic Spline Interpolation with Minimal Feed Fluctuation”, Trans. ASME, J. Manufac. Sc. And Eng., Vol.127/2, pp. 339-349.

  48. Maeda, O., Cao, Y.Z., Altintas, Y., 2005, “Expert Spindle Design System”, Int. J. Machine Tool Manuf. Eng., Vol. 45, pp. 537-548.

  49. Larue, A., Altintas, Y., 2004, “Simulation of Flank Milling Processes”, Int. J. Machine Tools and Manuf., Vol. 45, pp. 549-559.

  50. Altintas, Y., Weck, M., 2004, “Chatter Stability in Metal Cutting and Grinding”, Annals of CIRP, Key Note Paper of STC-M, Vol. 53/2, pp. 619-642.

  51. *Cao, Y.Z., Altintas, Y., 2004, “A General Method for the Modeling of Spindle-Bearing Systems”, Trans. ASME, J. Machine Design, Vol.126, pp.1089-1104.

  52. Altintas, Y., Park, S., 2004, “Dynamic Compensation of Spindle Integrated Force Sensors”, Annals of CIRP, Vol. 53/1, pp. 305-308.

  53. Costes, J.P., Ko, P.L., Ji T., Deces-Petit C., Altintas Y., 2004, “Orthogonal cutting mechanics of maple: modeling a solid wood-cutting process”,  Journal of Wood Ssc. Vol.50 (1), pp. 28-34.

  54. *Merdol, D., Altintas, Y., 2004, “Multi frequency solution of chatter stability for low immersion milling”, Trans. ASME, J. Manufac. Sc. And Eng., Vol. 126/3, pp. 459-466.

  55. Park, S., Altintas, Y., “Dynamic Compensation of Cutting Forces Measured from the Spindle Integrated Force Sensor System”, Trans. ASME, J. Dynamic Systems, Measurement and Control, vol.126/3, pp.443-452.

  56. Merdol, D., Altintas, Y., 2004, “Mechanics and Dynamics of Serrated End Mills”, Trans. ASME, J. Manufac. Sc. and Eng., Vol.126/(2), pp. 317-326.

  57. Costes, J.P., Deces-Petit, C., Altintas, Y., Ko, P., 2003, “Estimated Stress and Friction Distributions on tool rake face in the medium density fiberboard cutting process”,  Forest Products Journal, Vol.53, No.11/12, pp. 59-66.

  58. Campomanes, M. L., Altintas, Y., 2003, “An Improved Time Domain Simulation for Dynamic Milling at Small Radial Immersions”, Trans. ASME, Manufacturing and Engineering and Science, Vol.125(3), pp. 416-422.

  59. Altintas, Y., Erkorkmaz, K., 2003, “Feedrate Optimization for Spline Interpolation in High Speed Machine Tools”, Annals of CIRP, Vol. 52/1, pp. 297-302.

  60. Park,S., Altintas,Y., Movahhedy, M.S., 2003, “Receptance Coupling for End Mills, International Journal of Machine Tools and Manufacture” , Vol. 43/9, pp. 889-896.

  61. *Woronko, A., Huang, J., Altintas, Y., 2003, “Piezoelectric Tool Actuator for Precision Machining on Conventional CNC Turning Centers”, Journal of Precision Engineering, Vol. 27, pp. 335-345.

  62. Lazoglu, I., Atabey, F., Altintas, Y., 2002, `` Dynamics of boring processes: Part III-Time domain modeling’’, Journal of Machine Tools and Manufacture, Vol. 42/14, pp. 1567-1576.

  63. Atabey, F., Lazoglu, I., Altintas, Y., 2003, “Mechanics of boring processes - Part II, Multi-insert boring heads”, International Journal of Machine Tools and Manufacture, Vol. 43/5, pp. 477-484.

  64. Atabey, F., Lazoglu, I., Altintas, Y., 2003, “Mechanics of boring processes - Part I’’ International Journal of Machine Tools and Manufacture, Volume 43/5, pp. 463-476.

  65. Lazoglu, I., Altintas, Y., 2002, “Prediction of tool and chip temperature in continuous and interrupted machining", International Journal of Machine Tools and Manufacture, Vol. 42/9, pp. 1011-1022.

  66. Altintas,Y., Woronko, A., 2002, “A Piezo Tool Actuator for Precision Turning of Hardened Shafts", Annals of CIRP, Vol. 51/1, pp. 303-306.

  67. G. Pritschow, Y. Altintas, F. Javone, Y. Koren, M. Mitsuishi, S. Takata, H. Van Brussel, M. Weck, K. Yamazaki, 2001, “Open Controller Architecture-Past,present and future”, Annals of CIRP, Vol. 50/2, pp. 446-463. (Key Note Paper).

  68. Movahhedy, M.R., Altintas, Y., Gadala, M., 2002, “Numerical Analysis of Cutting with Chamfered Tools”, Trans. ASME, J. Manufacturing Science and Engineering, 124 (2), pp. 178-188.

  69. *Altintas, Y., 2001, ``Analytical Prediction of Three Dimensional Chatter Stability in Milling”, Japan Society of Mechanical Engineers, International Journal Series C: Mechanical Systems, Machine Elements and Manufacturing, Vol. 44/3, pp. 717-723.

  70. Engin, S., Altintas, Y., 2001,“Modeling of General Milling Operations: Part II- Inserted Cutters’’, Int. J. Machine Tools and Manufacture, vol. 41, pp. 2213-2231.

  71. Engin, S., Altintas, Y., 2001,  “Modeling of General Milling Operations: Part I- End Mills’’, Int. J. Machine Tools and Manufacture, vol. 41, pp. 2195-2212.

  72. Altintas, Y., Engin, S., 2001, “Generalized Modeling of Mechanics and Dynamics of Milling Cutters”,  CIRP Annals, Vol.50/1, pp. 25-30. 

  73. Erkorkmaz, K., Altintas, Y., 2001, “High Speed CNC System Design: Part III - High Speed Tracking and Contouring Control of Feed Drives”, Int. J. Machine Tool Manuf., pp. 1637-1658.

  74. Erkorkmaz, K., Altintas, Y., 2001,  “High Speed CNC System Design: Part II - Modeling and Identification of Feed Drives”, Int. J. Machine Tool Manuf., pp. 1487-1509.

  75. Erkorkmaz, K., Altintas, Y.,  2001, “High Speed CNC System Design: Part I - Jerk Limited Trajectory Generation and Quintic Spline Interpolation”, vol. 41, pp. 1323-1345.

  76. Zhu, W.H., Jun, M.B., Altintas, Y., 2001, “A Fast Tool Servo for Precision Turning of Shafts on Conventional CNC Lathes”, Int. J. Machine Tool Manufacture, vol.41, pp. 953-965.

  77. *Altintas, Y., 2000, “Modeling Approaches and Software for Predicting the Performance of Milling Operations at MAL- UBC”, International Journal of Machining Science and Technology, vol. 4/3, pp. 445-478.

  78. Engin, S., Y. Altintas, F. Ben Amara, 2000, “Mechanics of Routing Medium Density Fiber Boards”, 2000 (September), Forest Products Journal, vol. 51, pp. 65-70.

  79. Dippon, J., Ren, H., Ben Amara, F., Altintas, Y., 2000, “Orthogonal Cutting Mechanics of Medium Density Fiberboards”, Forest Products Journal, vol. 50, No:7/8, pp. 25-30.

  80. *Altintas, Y., Erkorkmaz, K., Zhu, W.H., 2000, “Sliding Mode Controller Design for High Speed Feed Drives”, CIRP Annals, vol. 49/1, pp. 265-270.

  81. Movahhedy,M.R., Gadala, M.S., and  Altintas, Y., 2000, “ Simulation of Orthogonal Metal Cutting Process Using Arbitrary Lagrangian-Eulerian Finite Element Method”, Journal of Materials Processing Technology, vol.103, pp. 267-275.

  82. Erol, N.A., Altintas, Y., Ito, M., 2000, “Open Architecture Modular Tool Kit for Motion and Machining Process Control”, Trans. ASME/IEEE J. Mechatronics, vol.5, No.3, pp. 281-291.

  83. Ren, H., Altintas, Y., 2000, “Mechanics of Machining with Chamfered Tools”, Trans. ASME, J. Manufacturing and Engineering and Science, vol. 122, pp. 650-659.

  84. Movahhedy, M. R., Gadala, M. S., Altintas, Y., 1999, “Simulation of Chip Formation in Orthogonal Metal Cutting Process: An ALE Finite Element Approach”, International Journal of Machining Science and Technology, vol. 4, pp. 15-42.  

  85. Liu, Q., Altintas, Y., 1999, "Online Monitoring of Flank Wear in Turning with Multi Layered Feed Forward Neural-Network", International Journal of Machine Tools & Manufacture, Vol. 39, pp. 1945-1959.

  86. Altintas,Y., Engin, S., Budak, E., 1999, “ Analytical Prediction of Chatter Stability and Design for Variable Pitch Cutters”, Trans. ASME, Manufacturing and Engineering and Science, vol.121, pp.173-178.

  87. Shamoto, E., Altintas, Y., 1999, “Prediction of Shear Angle in Oblique Cutting”, Transactions of ASME Journal of Engineering for Manufacturing Science and Engineering, vol. 121, pp. 399-407.

  88. Altintas, Y., Shamoto, E., Lee, P., Budak, E., 1999, "Analytical Prediction of Stability Lobes in Ball End Milling", Transactions of ASME Journal of Manufacturing Science ", Transactions of ASME Journal of Manufacturing Science and Engineering, vol.121, pp. 586-592.

  89. Van Luttervelt, C.A., Childs, T.H.C., Jawahir, I.S., Klocke, F., Venuvinod, P.K., Altintas, Y., Armarego, E., Dornfeld, D., Grabec, I., Leopold, J., Lindstrom, B., Lucca, D., Obikawa, T., Shirakashi, Sato, H.,1998, “Present situation and future trends in modelling of machining operations progress report of the CIRP working group 'modelling of machining operations”, CIRP Annals, Vol.47/2,pp:587-624.

  90. Altintas, Y., Erol, N.A., 1998, “Open Architecture Modular Tool Kit for Motion and Machining Process Control”, Annals of CIRP, Vol. 47/1, pp. 295-300.

  91. Altintas, Y., Lee, P., 1998, "Mechanics and Dynamics of Ball End Milling Transactions of ASME, Journal Manufacturing Science and Engineering,vol.120,  pp. 684-692.

  92. Budak, E., Altintas, Y., 1998, "Analytical Prediction of Chatter Stability Conditions for Multi-Degree of Systems in Milling. Part I: Modelling", Transactions of ASME, Journal of Dynamic Systems, Measurement and Control, vol.120, pp. 22-30.

  93. *Budak, E., Altintas, Y., 1998,"Analytical Prediction of Chatter Stability Conditions for Multi-Degree of Systems in Milling. Part II: Applications", Transactions of ASME, Journal of Dynamic Systems, Measurement and Control, vol.120, pp. 31-36.

  94. Bergs, T., Rodriquez, C.A., Altan, T., Altintas, Y., “Tool Path Optimization for Finish Milling of Die and Mold Surfaces - Software Development”, Transactions of the NAMRI/SME, Vol. XXIV, pp. 81-86, 1996.

  95. Altintas, Y., Lee, P., “A General Mechanics and Dynamics Model for Helical End Mills”, Annals of CIRP, Vol. 45/1, pp. 59-64, 1996.

  96. Altintas, Y., Lane, A. J., 1997, "Design of an Electro-Hydraulic CNC Press Brake", International Journal of Machine Tools & Manufacture, vol.37, No.1,pp. 45-59.

  97. Altintas, Y., Newell, N., Ito, M.,1996, "Modular CNC Design for Intelligent Machining. Part I: Design of a Hierarchical Motion Control Module for CNC Machine Tools", Transactions of ASME, Journal Manufacturing Science and Engineering, vol. 118, pp. 506-513.

  98. Altintas, Y., Munasinghe, K., 1996, "Modular CNC System Design for Intelligent Machining, Part II: Modular Integration of Sensor Based Milling Process Monitoring and Control Tasks", Transactions of ASME, Journal Manufacturing Science and Engineering, vol. 118, pp. 514-521.

  99. Lee, P., Altintas, Y., "Prediction of Ball End Milling Forces from Orthogonal Cutting Data", International Journal of Machine Tools and Manufacture, Vol. 36/9, pp.1059-1072, 1996.

  100. Shirashe, K., Altintas, Y., "Force and Surface Generation Mechanism with Variable Pitch Helical End Mills", International Journal of Machine Tools and Manufacture, Vol. 36/5, pp.567-584, 1996.

  101. Budak, E., Altintas, Y., Armarego, E. J. A., "Prediction of Milling Force Coefficients from Orthogonal Cutting Data", Transactions of ASME, Journal of Manufacturing Science and Engineering (former name: Journal Engineering for Industry), Vol. 118/2, pp. 216-224, 1996.

  102. Yucesan, G., Altintas, Y., "Prediction of Ball End Milling Forces", Transactions of ASME, Journal Engineering for Industry, vol. 118/1, pp.95-103, 1996.

  103. Gaida W. R, Rodriquez, C. A., Altan, T., Altintas, Y., "Preliminary Experiments for Adaptive Finish Milling of Die and Mold Surfaces with Ball-nose End Mills", Transactions of NAMRI/SME, Vol. XXIII, pp. 193-198, 1995.

  104. Altintas, Y., Budak, E., "Analytical Prediction of Stability Lobes in Milling", Annals of CIRP, Vol. 44/1, pp. 357-362, 1995.

  105. Koenig, W., Altintas, Y., Memis, F., "Direct Adaptive Control of Plunge Grinding Process Using Acoustic Emission (AE) Sensor", (Completed in TH Aachen), International Journal Machine Tools & Manufacture, vol. 35/10, pp. 1445-1457, 1995.

  106. Budak, E., Altintas, Y., "Modeling and Avoidance of Static Form Errors in Peripheral Milling of Plates", Int. J. Mach. Tools & Manufacture, Vol. 35/3, pp. 459-476, 1995.

  107. Altintas, Y., Munasinghe, W. K., "A Hierarchical Open Architecture CNC System for Machine Tools", Annals of CIRP, Vol. 43/1, pp. 349-354, 1994.

  108. Budak, E., Altintas, Y., "Peripheral Milling Conditions for Improved Dimensional Accuracy", International Journal of Machine Tools & Manufacture, Vol. 34/7, pp. 907-918, 1994.

  109. Weck, M., Altintas, Y., Beer, C., "CAD Assisted Chatter Free NC Tool Path Generation in Milling", (Completed in TH Aachen), International Journal of Machine Tools & Manufacture, Vol. 34/6, pp. 879-891, 1994.

  110. Yucesan, G., Altintas, Y., "Improved Modeling of Cutting Force Coefficients in Peripheral Milling", International Journal of Machine Tools & Manufacture, Vol. 34/4, pp. 473-487, 1994.

  111. Spence, A., Altintas, Y., "A Solid Modeller Based Milling Process Simulation and Planning System", Transactions of ASME Journal of Engineering for Industry, Vol. 116, pp. 61-69, 1994.

  112. Altintas, Y., "Direct Adaptive Control of End Milling Process", International Journal of Machine Tools & Manufacture, Vol. 34/4, pp. 461-472, 1994.

  113. *Altintas, Y., "Prediction of Cutting Forces and Tool Breakage in Milling from Feed Drive Current Measurements", Transactions of ASME, Journal of Engineering for Industry, Vol. 114, pp. 386-392, 1992.

  114. Altintas, Y., Chan, P. K., "In Process Detection and Suppression of Chatter in Milling with Variable Spindle Speed", International Journal Machine Tools & Manufacture, Vol. 32/3, pp. 329-347, 1992.

  115. Altintas, Y., Montgomery, D., Budak, E., "Dynamic Peripheral Plate Milling of Flexible Structures", Transactions of ASME, Journal of Engineering for Industry, Vol. 114, pp. 137-145, 1992.

  116. Altintas, Y., Spence, A., "End Milling Force Algorithms for CAD Systems", Annals of CIRP, Vol. 40/1, pp. 31-34, 1991.

  117. Spence, A., Altintas, Y., "CAD Assisted Adaptive Control for Milling", Transactions of ASME, Journal of Dynamic Systems, Measurement and Control, Vol. 113, pp. 444-450, 1991.

  118. Montgomery, D., Altintas, Y., "Mechanism of Cutting Force and Surface Generation in Dynamic Milling", Transactions of ASME, Journal of Engineering for Industry, Vol. 113, pp. 160-168, 1991.

  119. Altintas, Y., Ordubadi, F., Sassani, F., "Design and Analysis of Adaptive Controllers for Milling Process", Transactions of Canadian Society for Mechanical Engineers (CSME), Vol. 14, No. 1/2, pp. 17-25, 1990. (Misspelled in the journal)

  120. Ma, C. C. H., Y. Altintas, "Direct Adaptive Cutting-Force Control of Milling Processes." AUTOMATICA, Vol. 26, No. 5, pp. 899-902, 1990.

  121. Spence, A., Altintas, Y., Kirkpatrick, D., "Direct Calculation of Machining Parameters from a Solid Model", Journal of Computers in Industry, Vol. 14, No. 4, pp. 271-280, 1990.

  122. Altintas, Y. and Peng, J., "Design and Analysis of a Modular CNC System", Journal of Computers in Industry, Vol. 13, No. 4, pp. 305-316, 1990.

  123. Altintas, Y., Yellowley, I., "In Process Detection of Tool Failure in Milling Using Cutting Force Models", Transactions of ASME, Journal of Engineering for Industry, Vol. 111, pp. 149-157, 1989.

  124. Altintas, Y., Yellowley, I., and Tlusty, J., "The Detection of Tool Breakage in Milling Operations", Transactions of ASME, Journal of Engineering for Industry, Vol. 110, pp. 271-277, 1988. (Citation : 49, not included in Scopus)

  125. Altintas, Y., "In-Process Detection of Tool Breakage Using Time Series Monitoring of Cutting Forces", International Journal of Machine Tools & Manufacture, Vol. 28, No. 2, pp. 157-172, 1988.

  126. Altintas, Y. and Yellowley, I., "The Identification of Radial Width and Axial Depth of Cut in Peripheral Milling", International Journal of Machine Tools & Manufacture, Vol. 27, No. 3, pp. 357-365, 1987.


QuickFind

News